LOGO 700ManualMikado Model Helicopters GmbH • Friedrich-Klausing-Straße 2 • 14469 Potsdam • Germany phone +49 (0)331 23749-0 • fax +49 (0)331 23749-11
Manual LOGO 700 XXTREME - ©Mikado Model Helicopters GmbH -Page 10 8 Tail Boom MountingM2,5x12M2,5x12M2,5x12M2,5x12M3x12M2,5x6M2,5x6M2,5x6M3x12M3x16Lo
2x2x4x2x1x2x4xM3x12M3x16M2x12M2,5x10M2x5M2x66mm1x M22x3x5x2Note when mounting the ball links: If you nd it hard to clip the ball link on, t
5x3x6xM2,5x64x7x0,85xM2,5Note when mounting the ball links: If you nd it hard to clip the ball link on, turn it 180°. One side of the ball
2x2x4x2x2x2xM3x163x5x0,5M3x14M6x10M5M5x346,2x12x12xPlease apply grease to the O-rings and to the inner surface of the yoke.Please apply grease he
4x4x4x1xM3x16M4 StopM4x252xNote when mounting the ball links: If you nd it hard to clip the ball link on, turn it 180°. One side of the ba
BEC oderLipo-Empfängerakku 2S (1300-1500 mAh)You are required to use the adapter wire for the connection between the YGE-ESC and the VBar un
For mounting the ESC please use the plastic spacers included here. The connection to the carbon plate must not be electroconductive. Thi
The 12-cell lipo battery to be used with the LOGO 700 XXtreme needs to be mounted on the carbon battery plate, which is attached to the
Manual LOGO 700 XXTREME - ©Mikado Model Helicopters GmbH -Page 18 15 Main Rotor Blades and Tail Rotor Blades
The canopy of the LOGO 700 XXtreme is mounted via six attachment points. The four attachment points in the front ensure that the canopy sits well on
Additional precautions for the prevention of injuries or damage: Before you power on the helicopter, you must ensure that all screws and associated ha
Manual LOGO 700 XXTREME - ©Mikado Model Helicopters GmbH -Page 20 17 Overview Spare Parts Mainframe45154514M3x12 (6x)47114712M3x12M4x5M4x1024694290M3
Manual LOGO 700 XXTREME - ©Mikado Model Helicopters GmbH -Page 21 17 Overview Spare Parts Mainframe44694489 (Set)4585 (3x) 4734M3x10 (4x)45354541 (3m
Manual LOGO 700 XXTREME - ©Mikado Model Helicopters GmbH -Page 22 18 Overview Spare Parts Gear Box451645234521 6x13x54520M3x345194521 6x13x545204519M
Manual LOGO 700 XXTREME - ©Mikado Model Helicopters GmbH -Page 23 19 Overview Spare Parts Tail Boom4760 (2x)4756 (Set)47554759 (Set)45623x5x24561M3x1
Manual LOGO 700 XXTREME - ©Mikado Model Helicopters GmbH -Page 24 20 Overview Spare Parts Tail Rotor458147634565M2,5x12M3x16M2,5x84566452445684525452
Manual LOGO 700 XXTREME - ©Mikado Model Helicopters GmbH -Page 25 21 Overview Spare Parts Rotor Head4786 (M5x32)45084704M4x25M3x1645094507 (2x)470147
The mainframe of the LOGO 700 XXtreme is pre-assembled. You will nd it in Box 1. Note that the screws are not secured. You must use Loctite t
16mm 16mm16mm16mmABCD4x12x8x4x3x3x1x1x4x3x1xM2,5M3M2M2,5x6M2,5x8M2,5x10M2,5x12M3x12M2x1020xM2,5In the kit you will nd servo mounting sets for Futaba/
6x2xM3x12M3x121x3x2x4x2014x20x114x20x0,5Before mounting the main rotor shaft and the main gear, you need to remove the third bearing bl
2x4x4x4xM3x10M3x16M4x10M3x52x 3x5x1,22x M3x6Bag 5 contains two additional 1 mm washers. If necessary, you may adjust the distance of the can
4x4x1xM4x104x9x1M4x5Unscrew the motor plate and take it out of the chassis. Additionally you need the losen the screws of the counter-bear
2x2x1x1x1x2x1x1x M2M3x8M3x20M3x243x5x12,2M2,5x16M2x10M2x122x1x2x2x4x2x2x2x1x2x1x6xM3M2,53x7x0,55x10x45x10x43x6x2,57x10x0,55x7,8x0,63x5x0,54,5x2Mount
2x2x2x2x M3M3x163mmM3x16Before pushing in the torque tube, please ensure that the inside of the boom is clean. If necessary, clean it out with a piece
Komentáře k této Příručce